7/25/2023 0 Comments System shock 2 aux storage 5 code![]() Wall Mount Omni Antenna, 4-port, with RP-TNC connectors. ![]() Low Profile Self-Identifying Antenna, White, with RP-TNC connectors. Low Profile Antenna, White, with RP-TNC connectors. List of External Antennas Supported on C9120AXE and C9120AXPĭipole Antenna, Black, with RP-TNC connectors.ĭipole Antenna, Gray, with RP-TNC connectors.ĭipole Antenna, White, with RP-TNC connectors.ĭipole Self-Identifying Antenna, White, with RP-TNC connectors.Ĭeiling Mount Omni Antenna, 4-port, with RP-TNC connectors.Ĭeiling Mount Omni Self-Identifying Antenna, 4-port, with RP-TNC connectors. This includes information on the time stamp, signal strength, packet size, etc. It captures and forwards all the packets from the clients on that channel to a remote machine that runs Airopeek or Wireshark (packet analyzers for IEEE 802.11 wireless LANs). ■ Sniffer-In the wireless sniffer mode, the AP starts sniffing the air on a given channel. ■ Monitor-This is the monitor-only mode for the Cisco AP. ■ FlexConnect-FlexConnect mode for the Cisco AP. ![]() ■ Local-This is the default mode for the Cisco AP. The AP also supports the following operating modes: The AP supports both Cisco Embedded Wireless Controller and lightweight deployments (using Cisco Wireless Controllers). CleanAir delivers proactive, high-speed spectrum intelligence across 20-, 40-, and 80-, and 160-MHz-wide channels to combat performance problems arising from wireless interference. ■ Cisco CleanAir technology enhanced with 160MHz channel support. ■ Optimized AP Roaming for ensuring that client devices associate with the AP in their coverage range that offers the fastest data rate available. ■ Cisco Digital Network Architecture (DNA) support enables Cisco Connected Mobile Experiences, Apple FastLane and Cisco Identity Services Engine. This provides significant energy savings for battery-operated devices. ■ New power savings mode called Target Wake Time (TWT) which allows the client to stay asleep and wake up only at pre-scheduled (target) times to exchange data with the AP. ■ Spatial Reuse (also known as Basic Service Set (BSS) coloring) which allows APs and their clients to differentiate between BSSs, thus permitting more simultaneous transmissions. ■ Intelligent Capture probes the network and provides Cisco DNA Center with deep analysis. ■ Cisco RF ASIC, a fully integrated Software Defined Radio (SDR), that can perform advanced RF spectrum analysis and delivers features like CleanAir, Wireless Intrusion Prevention System (WIPS), and DFS detection. ■ Integrated Bluetooth Low Energy (BLE) radio to enable IoT use cases such as location tracking and wayfinding. see the Checking the Access Point LEDs for information on the colors of the LED status indicator. – Recovery push button (enables partial or full system configuration recovery) ■ The following hardware external interfaces: ■ Orthogonal Frequency Division Multiple Access (OFDMA)-based scheduling for both downlink and uplink ■ Multiuser Multiple-Input Multiple-Output (MU-MIMO) technology with 4 spatial streams for downlink. ■ Simultaneous 4x4 MIMO with four spatial streams for both 2.4 GHz and 5 GHz bands ■ Four radios-a 4x4 XOR radio for 2.4 GHz or 5 GHz, a single band 4x4 radio for 5 GHz, a 2.4 GHz radio that can be used with BLE, Zigbee, Thread and other 802.15.4 protocol devices, and an auxiliary radio for 2.4 GHz and 5 GHz. ![]() ■ External antennas on the 9120AXE and 9120AXP AP models (C9120AXE-x, C9120AXE-EWC-x, C9120AXP-x and C9120AXP-EWC-x).
0 Comments
Leave a Reply. |